AngelOfPlague Posted November 26, 2014 Share Posted November 26, 2014 I just got a squad of 5 Cataphractii Terminators off of ebay, and wanted to convert them into Deathwing Knights (hopefully, if the people I play against allow it, using them as regular Knights with a cosmetic change), and I was wondering if anyone had any experience with using 40k bits (maces and Storm Shields specifically) on models like this. The maces, I don't think will be an issue, as it's just the hand that attaches to the arm, but I can't figure out how to modify the Storm Shields so that they fit evenly. Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/ Share on other sites More sharing options...
Brother dean Posted November 26, 2014 Share Posted November 26, 2014 Stobz did some... Have a look a few pages back from this...http://www.bolterandchainsword.com/topic/231205-stobzz-dangles/page-36 Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/#findComment-3872124 Share on other sites More sharing options...
elmo Posted November 26, 2014 Share Posted November 26, 2014 This post shows the pre paint models from Brother Stobz Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/#findComment-3872132 Share on other sites More sharing options...
Brother dean Posted November 26, 2014 Share Posted November 26, 2014 Stobz says in a post that Cactus did some too but I am unable to find them right now... Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/#findComment-3872135 Share on other sites More sharing options...
Cactus Posted November 26, 2014 Share Posted November 26, 2014 You're absolutely right that the maces are simple and the shields are not. I'll dig out the link to my WIP thread and post it in the morning. Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/#findComment-3872275 Share on other sites More sharing options...
Brother dean Posted November 26, 2014 Share Posted November 26, 2014 Thanks Cactus... I'll need it for my tartaros Knights... Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/#findComment-3872279 Share on other sites More sharing options...
Interrogator Stobz Posted November 27, 2014 Share Posted November 27, 2014 As Cactus says, it's a bit of a pain in the rear to shave the arm out of the shield leaving the hand and other components, it's also a pain to get the new arm to fit snuggly without just smunching in a load of putty. Trial and Error are the ways forward :P Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/#findComment-3872326 Share on other sites More sharing options...
Cactus Posted November 27, 2014 Share Posted November 27, 2014 Here's the link to my WIP photos. http://www.bolterandchainsword.com/topic/260556-ptr-an-eclectic-mix-from-cactus-collection/?p=3286185 Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/#findComment-3872572 Share on other sites More sharing options...
Spaz431 Posted November 27, 2014 Share Posted November 27, 2014 Cool work there. Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/#findComment-3872615 Share on other sites More sharing options...
AngelOfPlague Posted November 29, 2014 Author Share Posted November 29, 2014 Awesome. Thank you for the links and advice! I'll try to get some pictures up when I get them done. Link to comment https://bolterandchainsword.com/topic/299725-converting-cataphractii-terminators/#findComment-3874123 Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.