Guest Posted April 23, 2019 Share Posted April 23, 2019 Just curious how people were painting and modeling Infiltrator helix adept. I see them as "wolf priest in training or candidates". So I was going to paint them black and give them deathsworn helms. Link to comment https://bolterandchainsword.com/topic/355475-painting-and-modeling-infiltrator-helix-adept/ Share on other sites More sharing options...
PeteySödes Posted April 23, 2019 Share Posted April 23, 2019 Yea that’s what I did. I can post a pic tomorrow, but I used a deathsworn helm, put some salves and balms on him and replaced the narthecium lite with a fang of morkai. I wasn’t planning on painting him in the full black but giving him a black rimmed pauldron. I’m pumped to see what everyone comes up with. Link to comment https://bolterandchainsword.com/topic/355475-painting-and-modeling-infiltrator-helix-adept/#findComment-5300655 Share on other sites More sharing options...
Wispy Posted April 23, 2019 Share Posted April 23, 2019 black armour for sure. Link to comment https://bolterandchainsword.com/topic/355475-painting-and-modeling-infiltrator-helix-adept/#findComment-5300673 Share on other sites More sharing options...
RikuEru Posted April 23, 2019 Share Posted April 23, 2019 I can post a pic tomorrow, but I used a deathsworn helm, put some salves and balms on him and replaced the narthecium lite with a fang of morkai. I wasn’t planning on painting him in the full black but giving him a black rimmed pauldron. I’m pumped to see what everyone comes up with. After I saw you using that helm, I HAVE TO do the same. (So I had to buy some Deathsworn... which caused me to order some Grey Slayers too. And a SW Tetminator Conversion Set. And Inferno. So... I blame you! But I also thank you.) I don't want to give him fully black armor tho. That would be 'too much' fpr a beginner?! Maybe make his narthecium arm black, akin to Deathwatch Veterans' silver arm. That way, he's still part of his pack brothers, but he is "marked" for a different task already. Anyone else wanna give him a power maul on his back? Like a Trainee's Crozium? But I haven't found a fitting model yet. Link to comment https://bolterandchainsword.com/topic/355475-painting-and-modeling-infiltrator-helix-adept/#findComment-5300690 Share on other sites More sharing options...
Guest Posted April 23, 2019 Share Posted April 23, 2019 Maybe just black pauldrons with the version of a Wolf priest symbol on the right? The only hesitation I have with the deathsworn helmets is I planned on using them for my reivers. Link to comment https://bolterandchainsword.com/topic/355475-painting-and-modeling-infiltrator-helix-adept/#findComment-5300696 Share on other sites More sharing options...
PeteySödes Posted April 23, 2019 Share Posted April 23, 2019 After I saw you using that helm, I HAVE TO do the same. (So I had to buy some Deathsworn... which caused me to order some Grey Slayers too. And a SW Tetminator Conversion Set. And Inferno. So... I blame you! But I also thank you.) I don't want to give him fully black armor tho. That would be 'too much' fpr a beginner?! Maybe make his narthecium arm black, akin to Deathwatch Veterans' silver arm. That way, he's still part of his pack brothers, but he is "marked" for a different task already. Anyone else wanna give him a power maul on his back? Like a Trainee's Crozium? But I haven't found a fitting model yet. Oof shows how out of it I am that I posted that pic already lol. At any rate I wear my “bad influence” mark proudly! Just in case though: I’m going to keep mine pretty simple without a crozius etc. I want it to read priest withou mucking it up for my opponents should I ever go full primaris and need a proper one. I think it a solid idea though so you should try it! Link to comment https://bolterandchainsword.com/topic/355475-painting-and-modeling-infiltrator-helix-adept/#findComment-5300815 Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.