Jump to content

Recommended Posts

The middle guy looks really cool, good use of the cataphron parts,

though I`m not really feeling that chainsword-hammer :tongue.: .

No one WANTS to feel the Thunderchainhammer. That would just be messy.

Also was mode of an experiment/ lacking an actual left handed T-hammer, plus my usual need for something a little over the top (as per my love of old school horror, you neeeeeed something OTT)

Link to comment
Share on other sites

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/2016-05-29%2019.02.53_zpsg7lnxrkp.jpg

 

What could this be, I wonder?

 

It's not often I Quintuple post, however this is appropriate as I have prepared vow 5. Enjoy.

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/2016-05-30%2011.10.32_zpsgsqqutyq.jpg

 

Edit: will just be for fun now obviously ^_^

Edited by helterskelter
Link to comment
Share on other sites

This is prep my friend :p all is well in the world and the vow 2 is properly in order with captain semper don't you worry. I'm only posting what I Consider interesting to others here :)

 

Edit: I'll bring it all across so you can see what I'm up to anyway :p

Edited by helterskelter
Link to comment
Share on other sites

Thought I'd poot this tutorial over here too. Spread the lurve

 

Sorry for the double post but this eve I thought I'd try and do something that may be useful to some brothers and sisters, first a PICTURE HEAVY WARNING so I bring you:-

The Helterskelter Telerac Pattern Volkite Culverin mounting procedure!

 

What you will need:

Superglue

Tweezers

A take out plastic tub or other suitable wide tub that can withstand boiling water

One pre built marine to the degree shown

Your clean Volkite parts

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/20160604_194909_zpsv7ualb0o.jpg

 

Step one: using the superglue, glue together your Culverin rig as shown. While this is drying boil the kettle and fill your recepticle. WARNING BOILING WATER CAN CAUSE SERIOUS HARM!!! BE SAFE, IF YOU ARE A YOUNGER FRATER FOLLOW THIS TUTORIAL WITH A BUDDY OR PARENTS

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/20160604_195134_zpsvedco6wr.jpg

 

Step 2: using the tweezers, lift your rig and carefully submerge into the water, it will take about 10 seconds, if that, to go as floppy as you need to work the piece into place

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/20160604_195329_zpskds9dtqw.jpg

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/20160604_195334_zps3w7kmsqw.jpg

 

Step 3: remove the piece from the water, carefully dripping away excess water, we now have around 30 seconds to work the piece on place, i have asbestos fingers with callous' due to guitar playing and gardening so I can handle parts with little to no problem from the heat, you may not be so lucky so be careful! Line up the back pack and the hand to their relevant positions, but it is OK if you don't get it first, second or even third try, be patient, the water stays hot for a good while, you will get it :) once positioned, hold until the rig is reasonably firm.

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/20160604_195546_zpskweh6kpa.jpg

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/20160604_195600_zpsgydh6pim.jpg

 

Step 4: use your superglue to cement the rigs position and when dry finish your model!

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/20160604_195703_zps7uoz8r2e.jpg

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/20160604_200218_zpsuyamndhb.jpg

 

 

And that my dear members of the Martian Death Ray Club is that, I hope this may help some overcome their fear of FW pipe bending, or just generally be a little bit useful.

 

Link to comment
Share on other sites

  • 2 months later...

Holy Mother of Pearl!!

 

What bits did you use for your Fore Lord?

 

Also love the Volkite Executioner!

 

Hope the stress & depression are easing off of you fella!!

Edited by dantay_xv
Link to comment
Share on other sites

Holy Mother of Pearl!!

 

What bits did you use for your Fore Lord?

 

Also love the Volkite Executioner!

 

Hope the stress & depression are easing off of you fella!!

Thanks dude, it's getting there!

Parts for the forgeLord are gorgon terminator legs, kataphron destroyer body, cataphractii shoulder pads, iron father terminator arms, some mechanicum servo arm bits, and a very old GW bat

Link to comment
Share on other sites

How many of my brothers have you and your kind killed? Dozens? Hundreds? We weren't even at istvaan this company of mine, yet you hounded us anyway, no hails, no attempt at any kind of communication, only violence.

Now your brothers are but shadows and dust, who am I to deny you the same fate?

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/2016-08-20%2023.17.28_zpswpir3rtp.jpg

Link to comment
Share on other sites

Thanks for the love guys!

 

Now for a little bank holiday madness

 

http://i826.photobucket.com/albums/zz184/Lamenterkyle/Mobile%20Uploads/2016-08-29%2014.59.03_zpsoc7kvcwg.jpg

 

Excuse the rough paint job, it's taken me a number of years and various levels of sanity to find a way of painting yellow that doesn't push me over the edge and think I've finally found a way :)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.